Clean gamecube games

Dry the disc , using a dry portion of the cloth and wiping in the same style as you did in step 1. After all of the water is gone, let the disc sit for at least two minutes to completely dry before inserting it into the Nintendo GameCube.

Check for Unlicensed products. Make sure that you're using only licensed products with your Nintendo system. Unlicensed products are not tested for compatibilty and may not work correctly with all games. Try playing the game without the unlicensed accessory. Check for specific game issues. Some games may have known issues or game play elements that appear as problems. Ensure the game is being loaded properly. With the power turned off on the system, replace the Game Disc label side up in the system, press down gently on the Game Disc until it locks on the center hub.

Close the Disc Cover and press the power button ON to see if the game comes on the screen. Look for obvious physical damage to the disc. Remove the Game Disc and check the non-labeled side for cracks, scratches, smudges, or dirt.

The Nintendo GameCube has extensive error correction capabilities and minor scratches or contamination should not cause issues in most cases. GameStop would offer to allow you to trade in the system as defective for a greatly reduced price towards a replacement.

Paste-based toothpaste acts as a mild abrasive that levels out the scratch, removing it or making it less noticeable.

The laser that reads the CD needs to bounce evenly off the smooth, reflective surface. Toothpaste is just abrasive enough to wear down scratched areas to a smoother surface. Signs of disc rot On CDs, the rot becomes visually noticeable in two ways: When the CD is held up to a strong light, light shines through several pin-prick-sized holes. Discoloration of the disc, which looks like a coffee stain on the disc. See also CD bronzing. Dampen a clean, soft, cotton cloth with water.

Use straight strokes and wipe the disc non-labeled side from the inside rim to the outside rim. Using a dry part of the cloth, repeat step 2 to dry the disc. This screw is a 4. Get a clean toothbrush no toothpaste and a cup of warm tap water not too hot. Slightly dip the toothbrush in the water the toothbrush should not be dripping wet and scrub the area of the Controller around the buttons and control stick. On game consoles, many times it is simply a software signal. Depending on how much damage occurs to the optical disc, most products can get repaired up to 50 times using this methodology.

By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article methods. Tips and Warnings. Related Articles. Article Summary. Method 1. Clean only when necessary. Clean the disc if you notice dirt or dust on the non-labeled side, or if your console or computer can't run the disc. Frequent cleaning is unnecessary and increases the risk of scratching the disc.

Find a soft, clean cloth. Always use a smooth-textured, lint-free material, such as cotton or microfiber cloth. Avoid rough materials such as facial tissues or paper towels. Dampen a small area of the cloth. Use regular tap water to wet a small area of the cloth, then squeeze it out to remove excess water. Never use household cleaning products, which can ruin the disc. Hold the game disc by its rim. Do not place your fingers on the surface of the disc.

Turn the game disc so the non-labeled, reflective side faces you. If the labeled side is clearly dirty, you can use this same method — but be extremely careful, as wiping the labeled side too vigorously can destroy the data on some game discs. Wipe the disc surface from the center outward with the wet cloth.

Gently wipe the disc with the wet cloth, starting from the center hole and moving in a straight, short line to the rim. Repeat until the entire disc has been wiped. Never move the cloth in circles around the disc, as this can damage it. Repeat with the dry area. Wipe the same side of the disc a second time. This time, use the dry portion of the cloth to remove moisture.

Take care to use the same straight strokes, from the center of the disc outward. Dry wiping is more likely to scratch the disc than wet, so be extra gentle during this step. Wait two minutes before testing. Put the disc down with the reflective side face-up.

Wait at least two minutes to allow the remaining moisture to evaporate. Once the disc is completely dry, put the disc into the disc drive of your game console or computer and check whether the problem is fixed.

If there are still problems, try the other methods below. If your other games also won't run, clean your disc drive. Method 2. Understand the risk. Most game disc manufacturers do not recommend using anything but water, but that's not always going to get the job done. These alternatives below are listed with the safest methods at the top, increasing in risk as you move down the list. Always use gently motions when cleaning to reduce the chance of scratches.

Mail your disc to a repair service. If you aren't prepared to risk damage, search online for a mail-in disc repair service in your country. These services may have buffing machines or cleaning products that are not commercially available. Remove fingerprints and grease with rubbing alcohol. This method will not repair scratches, but should remove grease stains. Apply a dab of isopropyl alcohol to a clean cloth, and rub the disc from the center to the rim.

Carefully wipe off moisture with a dry cloth with the same motions, then let sit for two minutes so it is completely dry. Since dry cloths can cause scratches, some disc owners prefer to let the disc air-dry for half an hour or more instead. Purchase a disc cleaner spray. If the game still won't boot up, purchase a "disc repair" product in spray bottle form and follow the instructions on the packaging to clean the disc.

Using a disc repair buffing wheel or other machine that comes with the disc repair product is highly discouraged, as these can cause damage.

Use a non-whitening, non-tartar-control toothpaste. Toothpaste is slightly abrasive, and can polish off scratches with low risk of causing more damage. Apply the toothpaste as you would water or rubbing alcohol, as described above. The toothpaste must be in paste form. Don't use a gel, liquid or powder. Select a safe polish.