Install the 8 mm and 6 rnrn cylinder head cover bolts and tighten them in a crisscross pattern i n 2 or 3 steps. Page MEMO Page 44 N m 4. Page 8. Take care not to damage the cylinder wall and piston. Do not damage mating surfaces by using a screwdriver when removing the cylinder. Camshaft lubricating oil is fed through the oil passage in the cylinder.
Remove the 6 mm cylinder bolts. Remove the cam chain guide front. Remove the four 10 mm cylinder bolts and washers. Do not strike the Remove the cylinder. Clean carbon deposits from the piston.
Page Check the top of the cylinder for warpage with a straight edge and feeler gauge across the studs and bolt holes as shown.
The rings should be able t o move in their grooves without catching. Page Measure piston pin hole I. Take the maximum reading to determine the I. Measure the piston pin at three points. To install the oil ring, install the spacer first, then install the side rails. Do not align the piston pin clip end gap with the piston cutout. Page Apply oil to the cylinder wall, piston and piston ring outer surfaces.
Route the cam chain through the cylinder and install the cylinder over the piston while compressing the piston rings with your fingers.
Page N m Page 9. Engine oil viscosity and level and the use of oil additives have an effect on clutch operation. Remove the two bolts and clutch cable holder, and disconnect the clutch cable from the clutch lifter arm. Remove the bolts, oil pipes O-rings and dowel pins from the right crankcase cover. Remove the O-ring and oil pump driven sprocket from the oil pump.
Check the lifter arm spindle for wear or damage. Check the return spring for fatigue or damage. Remove the bolts and springs. Remove the pressure plate and lifter piece. Remove the clutch discs and plates. Unstake the clutch center lock nut. Be carefulnor to damage the threads. Page Remove the lock washer, plain washer and clutch center. Remove the thrust washer, clutch outer and clutch outer guide. The bearing should turn smoothly and quietly. Also check that the outer race of the bearing fits tightly in the pressure plate.
Replace the Check the plate warpage o n a surface plate using a clutchdiscsand Page Measure the mainshaft O. Install the clutch outer and thrust washer. Install the clutch center and plain washer. Apply oil to the threads and seating surface of a new clutch center lock nut and install it onto the mainshaft. Hold the clutch center with the special tool and tighten the lock nut.
Page Apply oil to the clutch lifter piece whole surface and lifter bearing. Install the clutch lifter piece and pressure plate. Install the clutch springs and bolts. Tighten the bolts in a crisscross pattern in several steps. Install the right crankcase cover page Page Apply oil to the primary drive gear nut threads and seating surface. Install the washer and primary drive gear nut. Remove the oil pump page Install the clutch outer onto the mainshaft.
Install the special tool between the primary drive and driven gears as shown and tighten the primary drive gear nut. Page Flywheel bolt Apply locking agent to the threads. Remove the gasket and dowel pins. Remove the spacer, starter idle gear and shaft from the left crankcase cover. Remove the seatlrear fender page Disconnect the alternator connectors.
Page Remove the nut, seven bolts and the left crankcase cover. Remove the starter reduction gear shaft and gear. Remove the two ignition pulse generator bolts and wire clamp. Coat new O-ring with oil and install it into the starter motor groove..
Install the dowel pins and a new gasket Install the left crankcase cover, being careful not to pinch the neutral switch wire. Page Route the alternator wire properly page Connect the alternator connectors. Install the seatlrear fender page Install the starter idle gear shaft, gear and spacer in the left crankcase cover. Install the dowel pins and new gasket.
Install the starter idle gear cover and tighten the four bolts securely. Page Starter Clutch Remove the flywheel using the special tool. Remove the starter driven gear while turning it coun- terclockwise.
Check the starter clutch outer and sprag clutch for abnormal wear or damage. Check the starter driven gear teeth for wear or damage. Page Apply locking agent t o the starter clutch bolt threads. Install the starter clutch assembly onto the flywheel and install the bolts. Hold the flywheel with the special tool and tighten the bolts.
Page Apply oil to the flywheel bolt threads and seating sur- face, and install the special washer and bolt. Hold the flywheel with the special tool and tighten the bolt.
To service these parts, the engine must be removed from the frame section 6. Page Remove the gasket and dowel pins. Pull the gearshift plate away from the shift drum and remove the gearshift spindle. Measure the gear I. Page Check the gears for freedom of movement or rotation on the shaft. Engage the mainshaft and countershaft gears. Apply oil to the countershaft oil seal lip. Install the mainshaft and countershaft assemblies as to install a set into the left crankcase.
Install the shift fork shaft through the shift forks and into the left crankcase. Apply oil to the gearshift spindle oil seal lip Install the gearshift spindle by aligning the return spring ends with the spring pin bolt while pulling the gearshift plate. Page If the left crankshaft bearing is left on the crankshaft, remove it using the bearing puller with a suitable protector. NOTE: Always replace the left crankshaft bearing with a new one when the crankshaft is removed.
Drive the crankshaft bearing into the left crankcase with the marking side facing up. Page Bearing Remover, 15 Mm cob. Assemble the special tools onto the crankshah. Draw tne crankshatt into the bearing 'nner race.
Page Apply oil to new bearings. Drive the mainshaft, crankshaft and balancer bear- ings in with the marking side facing up using the spe- cial tools. Page Remove the mainshaft bearing using the special tools.
Always wear insulated gloves when handling the crankcase after has been heated. Install the dowel pins and a new gasket. Page Install the cam chain drive sprocket onto the crank- shaft, b y aligning the wide groove w i t h the wide tooth. Install the cam chain onto the drive sprocket and through the crankcase.
Apply locking agent the cam chain tensioner bolt threads. Remove the handlebar cover attaching bolt, being careful not to let the bolt fall into the steering shaft. Remove the cover by releasing its ends off the han- dlebar carefully. Page Note Install the upper holders with the punch marks facing forward. Install the four bolts and tighten the forward bolts first, then tighten the rear bolts.
Wait 3 minutes and install the grip. Align the slit of the lever bracket with the punch mark on the handlebar, and tighten the upper bolt first, then the lower bolt. Connect the clutch switch to the connectors and install it into the clutch lever bracket. Bend down the lock washer tab and remove the pivot nut, lock washer, throttle arm and return spring, then the throttle lever with the plastic washer. Disconnect the throttle cable from the throttle arm. DUST Turn the inner race each bearing with your finger.
The bearings should turn smoothly and quietly. Also check that the bearing outer race fits tightly in the hub. Install the distance collar with the large dia. Drive in a new outer bearing squarely with the mark- ing side facing up until is fully seated. NOTE: Do not interchange the left and right tires. Install the wheel nuts with the tapered side facing inward and tighten them.
Lube the bead area with water, pressing down on the tire sidewalllbead area in several places to allow the water to run into and around the bead. If your kit does not have instruc- tions, use the procedures provided here. Check the tire for puncturing objects. Chalk mark the punctured area and remove the punc- turing object. Remove the lining from the patch and center it over the injury.
Press the patch against the injury using a special NOTE: Allow cement to dry until tacky before applying patch. Press the spherical bearing out of the arm pivot. Tighten each nut to the specified torque and further tighten until its grooves align with the cotter pin hole. Install the following: - tie-rod into knuckle page - wheel hub and front wheel page , Check the damper unit for leakage or other damage. Replace the shock absorber assembly if necessary.
Coat new dust seal lips with molybdenum disuifide paste and install them into the lower pivot. Remove the joint nuts by holding the joint stud flat surfaces. Remove the tie-rods from the knuckles and steering shaft.
Remove the cotter p n and tne steering shaft end Remove the steerlng snaft and shaft co lar from tne frame. With a Haynes Online Manual in an online format you get all the trusted content of a printed manual, with additional features to help you get the job done. Take your entire manual with you on every journey. Have a problem? This is really popular from the society simply because manual book is regarded as complementary package.
Sportrax EX. Maintenance schedule Simple weekly checks and servicing guides to keep you on the road. The website will process and demonstrate you the end result. In addition to, the manual can also be obtained through third-party websites. On this case, you have to be seriously careful for the reason that the manual could possibly not be as valid as 1 you find within the official site of your automaker.
In addition, some web-sites call for you to register, for that reason it truly is considered as impractical. For trustworthy third party web-site, you might decide on eBay or Amazon.
On the other hand, in the event you come across Honda ex Service Manual Free Download from third get together web page, especially unreliable 1, the content may possibly be diverse. Honda Owners Manual. Prev Article.
0コメント